Compression garbage trucks work

Xigong Chusheng (Hubei) Special Purpose Vehicle Manufacturing Co., Ltd. Compression garbage truck

● Frame structure   The dustbin is made of reinforced beam and steel plate welded to form a solid frame structure. The bottom surface is a concave plane. The sides and the top surface are arc surfaces. The appearance is beautiful, the weight is light, the force is good, and the deformation is not. The shovel is made of steel pipe skeleton and folding panel. The structure is not only compact, but also can make the garbage evenly distributed, and the discharging is clean and thorough; the filling device is mainly composed of the filler shell, slide plate, scraper and other components, and each component adopts a beam or box structure with good stress. ,Strong structure, light weight;

● Sealing eliminates secondary pollution   Garbage is closed in the process of compression loading and transportation. The interface between the waste container and the filler is sealed with a special rubber seal. The front end of the waste container has a recovery tank consisting of a waste container and a rear shovel with a volume of 1.35 m . There is a recovery tank with a volume of 0.3 m in the lower part of the filling device. The water inlet can receive the sewage that leaks due to aging or damage of the sealing strip between the waste container and the filler during use. The cylinder is installed on the recovery tank. Or manually controlled drain valve to facilitate the discharge of sewage at the designated place. The filler cap completely covers the filling inlet of the filler, eliminates the phenomenon of dust emission caused by the disturbance of the tail air during the transportation process, and is more beautiful;

● Electro-hydraulic joint control   The vehicle's control system makes full use of the advantages of electronic control, pneumatic control, and hydraulic control. The electronic control system controls the air control system, and the air control system controls the hydraulic valve set, effectively solving the interface problem between the hydraulic system and the electrical system. , Full use of multi-way valve than the electromagnetic valve to resist the characteristics of oil pollution, eliminate the stuck valve phenomenon, improve the use of reliability and efficiency;
●
Hydraulic lift safety circuit   In the hydraulic system of the lift filler, an explosion-proof valve is provided. The valve blocks the direct connection between the lift cylinder and the hydraulic hose. Even if the fuel pipe bursts, the filler will not drop suddenly and cause a serious accident. This improves the use of the valve. safety;
●
Automatic, manual operating system    There are two kinds of automatic and manual operations for each agency's work, such as the failure of automatic operation, manual operations to complete the operation of the organization and unloading garbage, both to ensure the efficient operation of garbage trucks, but also for debugging, maintenance and troubleshooting Great convenience;
●
Automatic control of engine power output   The engine power output control, that is, the throttle control, can be fully controlled by the electrical system to meet the power requirements during the waste press filling cycle and pushing and unloading. Under other operating conditions, the engine is automatically at idle, reducing power loss and failure. Incidence, lower fuel consumption, and increase economic efficiency;
●
advanced electronic control system   Imported PLC (programmable logic controller) integrated control, control circuit generated in the PLC , the logic circuit to ensure that the operation instructions in order to perform, while ensuring that the interlock between the operation instructions, the only external line connection, reducing the occurrence of failure Rate, to avoid accidents caused by misuse, improve the reliability; special emergency brake button can be set to make the garbage compaction mechanism stop in any state or anywhere, to protect the safety of workers and equipment;
●
Convenient operation control   The job control box is installed in the cab and rear respectively. The operation control box in the cab can control pushing and unloading and select the operation mode (such as automatic or manual). The rear job control box controls the press filling mechanism and the turnover mechanism. The operation is very easy to use. Especially in landfills, operators can complete discharging and sewage discharge without getting off the train. Can be equipped with remote control device according to user requirements;
● A variety of bucket (bucket) mechanism    According to different garbage collection methods, different users can choose different bucket-turning mechanisms: Turn standard waste iron drums ZBT59003-88 ( 300 liters), plastic trash cans ( 240 liters), and truck litter bins ( 800 liters) ), a sealed garbage bin ( 1400 liters) and a large garbage bin ( 3,350 liters).

Xigong Gongchu Sheng (Hubei) Special Purpose Vehicle Manufacturing Co., Ltd. Compression garbage truck Working methods:

When the filling hopper is full of trash, the scraper opens, and the sliding board drives the scraper to move downwards, inserts garbage into the garbage and breaks it for the first time. The scraper sways forward and further compacts the garbage. The scraper moves into position and moves upwards with the skid. Compact the trash and fill it in the bin, then return to the starting position.   The whole working process is automatically controlled. When the garbage is continuously filled, the shovel pushes against the back pressure and gradually withdraws under the effect of the pressing force. The bidirectional compression of the garbage is realized and evenly distributed in the entire garbage can. When the compression garbage truck unloads the garbage in the processing (or landfill) yard, lift the filler and push the shovel backwards to push the garbage in the bin horizontally.

Cosmetic Packaging Case

Cosmetic Packaging Case,Compact Powder Case,High Quality Cosmetics Case

Plastic Injection Mold Co., Ltd. , http://www.vstmould.com