Operation and maintenance method of art glass equipment air compressor

First, the damage caused by impurities:
Air compressors, as the name implies, are machines that compress air. The source of air is the air around the equipment. If the air compressor is placed in a place where dust and dust gather for a long time, the service life will be greatly reduced. The reason is very simple. Particles or dust will not only scratch the cylinder as the air enters the cylinder, but also severely wear the piston and other components. Causes the equipment to be used without life. Therefore, when using the air compressor, we should place the air compressor in a place with a relatively clean air. Keep it ventilated and dry. It can be solved by the extension of the available air belt.
Second, oil and gas emissions:
There is moisture in normal air. When the air compressor is working, not only the air is compressed and output, but also a considerable part of the water is pressed into the machine. At the same time, the lubricating oil in the machine evaporates and then condenses, and it is easy to form an oil-water mixture. This oil-water mixture causes serious quality problems such as mottling and varnishing when painting, and it is a common phenomenon to block the muzzle during sand blasting. The most extreme example seen by Longxiang Art Glass, an air compressor has half a tank of water. Therefore, often putting this mixture of oil and water is one of the common tasks of maintaining air compressors. If possible, it is best to install a water filter.
Third, place the flat:
Some air compressors fall off due to improper maintenance of the wheels during use. Some users use a wooden block to support a corner. The air compressor shakes left and right while working. And many users are not too concerned about this kind of shaking. The actual situation is. When the air compressor is working, the four corners must be stable and high. Otherwise, unnecessary wear will be caused to the air compressor cylinder and the piston to reduce the life. It is often the case that if an air compressor wheel is removed, it is not far from being broken. So if the air compressor fulcrum falls off, be sure to find a way to weld one. Don't make a temporary padding.
4. Replenishment and replacement of lubricating oil:
Many customers have not replaced the lubricating oil until the air compressor is used badly. It is better to say that the air compressor is worn out rather than being used up. Most of the cylinder equipment needs to have lubricants to participate in the work. Just like a car, you will need to check regularly to add or replace lubricants. This is also the maintenance work that is often done. The oil level should be seen frequently, and the oil should be replaced regularly. If you find that the lubricating oil is quickly lost, you must stop the air compressor and check it for repair.

Comb idler is made by plain roller with welded spiral steel. It's used for cleaning conveyor belt. comb idler is setting in the position where unwanted debris will stick to the belt seriously. It removes the sticky material to keep belt clean and running stable, avoid misalignment. Usually, it's used in conjunction with sleeve rollers at the beginning of return run. comb idler roller diameter is fromφ76 to φ219

 

Comb Idler used in acid and alkali resistant industry of conveyor, comb idlers can replace the metal roller , nylon roller , long life , easy installation , custom center smooth transportation , reduce conveyor belt deviation and protection conveyor belts and other characteristics . comb roller superior performance than traditional iron roller , low wear coefficient , the proportion of small , light weight , easy to replace , and the low noise , smooth operation , more suitable for the working environment of the production conditions , high service life.

 

Comb Idler


 


 

Diameter mm

Length (Tube) mm

Bearing

89

315.380.465.600.750.950.1150

6204

108

315.380.465.600.700.750.790.950.1150.1400.1600

6205

133

465.600.700.750.790.800.900.950.4000.1100.1150.1400.1600.1800.2000.2200

6305 6308

159

600.700.790.800.900.950.1000.1050.1100.1120.1150.1250.1400.1500.11700.1800.2000.2200.2500.2800.3000.3150.

6306 6308

193.7

1100.1250.1400.1500.1600.1700.2200.2500.2800.3000.3150

6308

219

2200.2500.2800.3000.3150

6310

 

Comb idler usually use big clearance deep groove ball Bearing For Conveyor Idler roller.

Comb Idler

To be the first class, to do the best quality, to make users satisfied, to ensure customers relieved, are our enterprise purposes. Welcome bearing dealers` and Conveyor Idler manufacturers contact from all over the world, and become our partner.

 

Comb Idler

Comb Type Cleaning Roller,Comb Cleaning Roller,Comb Idler

Shandong Xinkaite Bearing Co., Ltd. , http://www.idlerbearing.nl