Manual Ceramic Slurry Knife Gate Valve (GPZ43TC)

GPZ43TC Manual Ceramic Slurry Knife Gate Valve 
Characteristics:
This valve is applicable for discharge and transportation of dry ash systems in power plants and storehouse pumps, or can be used as an on-off device for pipelines containing abrasive dry ash, water (such as cinder water ) and the like in mines, paper making, chemical engineering and so on, as an on-off for pipelines with both soft grains and corrosive media. Its working nominal pressure is 1.0MPa, applicable temperature is below 200 Deg C, and air supply pressure is 0.6-0.8MPa.

After the valve closed, it's fully sealed in any direction. Its middle body adopts WCB steel casting and seamless steel pipe welding. Its sealing surface adopts a hard sealing element.

Its feed inlet is fully through without any blocks, and it has an automatic compressed air anti-blcikage blowing unit, with strong abrasion resistance, a good sealability, a small starting load and with  little ash sezure of accumulation.

It adopts a high-grade toughened structural ceramic seal, featuring high mechanical strength, strong abrasion resistance, a long service life and a compact structure, which can be installed at any angle.

Special ceramics is different from general ceramics, its hardness even more than steel,
second only to diamond, and corrosion resistant, high temperature resistant!!!!! "" metal
valve with long easy to produce the gap, ceramic valve is not. Because of wear-resisting,
anti-corrosive, sealing strong, ceramic water valve very water saving. "" our valves can be
used 500000 times, if every switch 60 times, can use 22.8 years, this is metal valve can not do it. "

Main Parts and Materials
Application Specification
1. Design and Manufacture: JB/T 8691
2. Face to Face Dimension: GB/T 15188.2
3. Flange Dimension: GB/T 9113.1, ANSI B16.5  DIN 2543, JIS B2020
4. Inspection and Test: GB/T 8691
5. Material Standard: GB/T 12229 for Carbon Steel, GB/T 12230 for Stainless Steel

Main External and connecting Dimensions
 

  GPZ43TC Manual Ceramic Slurry Knife Gate Valve 
Characteristics:
This valve is applicable for discharge and transportation of dry ash systems in power plants and storehouse pumps, or can be used as an on-off device for pipelines containing abrasive dry ash, water (such as cinder water ) and the like in mines, paper making, chemical engineering and so on, as an on-off for pipelines with both soft grains and corrosive media. Its working nominal pressure is 1.0MPa, applicable temperature is below 200 Deg C, and air supply pressure is 0.6-0.8MPa.

After the valve closed, it's fully sealed in any direction. Its middle body adopts WCB steel casting and seamless steel pipe welding. Its sealing surface adopts a hard sealing element.

Its feed inlet is fully through without any blocks, and it has an automatic compressed air anti-blcikage blowing unit, with strong abrasion resistance, a good sealability, a small starting load and with  little ash sezure of accumulation.

It adopts a high-grade toughened structural ceramic seal, featuring high mechanical strength, strong abrasion resistance, a long service life and a compact structure, which can be installed at any angle.

Special ceramics is different from general ceramics, its hardness even more than steel,
second only to diamond, and corrosion resistant, high temperature resistant!!!!! "" metal
valve with long easy to produce the gap, ceramic valve is not. Because of wear-resisting,
anti-corrosive, sealing strong, ceramic water valve very water saving. "" our valves can be
used 500000 times, if every switch 60 times, can use 22.8 years, this is metal valve can not do it. "

Main Parts and Materials
Application Specification
1. Design and Manufacture: JB/T 8691
2. Face to Face Dimension: GB/T 15188.2
3. Flange Dimension: GB/T 9113.1, ANSI B16.5  DIN 2543, JIS B2020
4. Inspection and Test: GB/T 8691
5. Material Standard: GB/T 12229 for Carbon Steel, GB/T 12230 for Stainless Steel

Main External and connecting Dimensions
 

 

Our factory is located in Yangzhou, jiangsu province, has long history and many famous views. We are specialized in producing 3 to 5 axis single(double) colour drilling and tufting combination machine. Our products are widely used in all kinds of brushes, for example:electric toothbrush,travel toothbrush, cosmetic brush, nail polish brush, roller brush, dish washing brush, hair series of comb brush, massage brush, wooden brush, barbecue copper wired brushes,electrical series of vacuuming brush production industry.

Technical Parameters:

1. Weight: 1500kg

2. Planting method: Round wire

3. Production speed: 500 rpm

4. Planting peak: 65mm

5. Planting pore size: φ1.6-φ4.0

6. Storable procedures: 1000 models

7. X-axis travel: 400mm;

8. Y-axis travel: 320mm;

9. Z-axis travel: 160mm;

10. Air input pressure: 0.8MPa

11. Rated voltage frequency single phase: 220V, 50Hz

12. Machine power: 2.0kw

13. Machine dimensions: 1.14 meters long, 1.84 meters wide and 1.75 meters high

14. Packing size: 1.8 meters length, 2.1 meters width, 2.1 meters height (conforming to standard container requirements).

5 Axes Drilling And Tufting Brush Machine

5 Axis Numerical Disc Brush Machine,High Speed CNC Broom Machine,5 Axis High Speed Brush Machine,Automatic Disc Brush Machine

Yangzhou Blue State Digital Control Brush Equipment Co., LTD. , http://www.lbbrushmachine.com