Gas Alarm Installation Instructions

1. Alarm installation location: within 1.5 meters from the air source radius, well ventilated: (1) liquefied gas is heavier than air and installed at about 0.3 meters from the ground. (2) Natural gas, city gas, carbon monoxide, etc. are lighter than air and are installed about 0.3 meters from the ceiling.
2. The location where the alarm cannot be installed: the location where the air is not easy to circulate in the corner, the cabinet, etc .;
3. The gas alarm uses a wide range of voltages. Commonly, it is a 220V civilian voltage product. Generally, the voltage of 12V is relatively rare. The power supply method uses a telephone line interface. It is suitable for users with higher safety requirements. It is installed in the bedroom. Small and practical!
Application production and sales of the alarm you want in your heart 1. Power light: green light, lights up after power-on, and goes off when the alarm occurs.
Alarm light: red light, lights up when the alarm, and goes off when the alarm is stopped.
2. After turning on the power, after the green light is on or flashing for 3 minutes, the alarm starts to work normally.
3. When the detected gas reaches the alarm point, the alarm starts to alarm, the green light goes out, the alarm light turns on, and the buzzer emits an alarm sound of "B, B, B ...". When the concentration of the detected gas drops below the alarm point When the alarm stops, the alarm will stop. (Carbon monoxide alarm has delay function)
4. If the manual detection function is added, when the button is pressed, the green light goes out, the alarm light turns on, and the buzzer emits an alarm sound of "B, B, B ...".
5. If the combined exhaust fan function is added, when the alarm alarms, the connected exhaust fan will start to automatically remove harmful gases.
6. If the function of connecting manipulator or solenoid valve is added, when the alarm alarms, the connected manipulator or solenoid valve will automatically close the gas valve, thereby cutting off the harmful gas source.
7. If the networking function is added, the management center or control center receives the normally open and normally closed (NO, NC) signals at the same time when the alarm alarms. (For the wireless function added, the alarm host will receive the wireless signal for 2-3 seconds)
After the alarm, a pair of relay passive contact signals can be output (normally open, normally closed, jumper setting), which is used to control ventilation equipment or provide normally open or normally closed alarm contacts for other equipment.
When the flammable gas concentration in the environment reaches the set threshold, it can send out sound and light alarm signals, and can output relay passive contact signals.
When the surrounding environment flammable gas concentration drops below the response threshold, the detector in the alarm state will automatically return to the normal working state.

Characteristic:
Strong adhesion, waterproof and anti-corrosion
The high standard of glue,Can cover all kinds of angle, arc, concave and convex surface, pressure groove, roll edge etc.
Used for decoration material,furniture,table surface,or other relative material etc.
Max film covering width:300mm     heating power: 6kw 
Max process thickness: 90mm       overall dimensions:5000*600*1800mm
Min process length: 600mm         weight:2500kgs
Feeding speed:1-35m/min           max diameter of rolling cover material:400mm
Feeding motor power:1.5kw         max width of cover film 600/900/1200mm

 with scraping glue system to keep the glue spreading uniform, it is suitable for different complicate shape, as angle parts, around ARC, roughness, extruding shape, so as to get a excellent surface.
 THE best choice for indoor decorative .

We have the following features:
1. Good quality quality is our culture
2. Fast service  24 hours answering service Vip service for you
3. Good reputation  influence company
4.  Quick after-sale service
5. Professional in this industry for 7 years
6. with us your money is safe,your business is safe. 
7. We think our products will give you an edge over your competitors.
advantages of XINGBANG machine
NO items 
1 the panel are made by CNC Gantry Milling,dimensions tolerance is under 0.05mm.
2 The shaft had a scale,which can control the size of workpiece.
3 All tubes and the guide bars are chromed with 0.03-0.05mm.
4 we adopt Magnetic brake in our control system,which is about RMB1000.while others use air brake or belt brake. 
5 we use Aviation connector,which can be used for decades.
6 we use Bidirectional sophisticated glue knives.which made by Japanese material.
7 high-precision rolling guide are imported from taiwan.
8 excellent silicon gel wheels
9 all french Schneider brand electrical control system 
10 each machine and compontes to be tested twice before shipment.(we have QC department)
11 our production aea about 10000 square meters.
12 we sell about 200sets woodworking machines each month.
13 our hot adhensive machines are NO 1 sales in domestic market,Quality stability has been recognized by the majority of our customers.
14 we have 10 Senior professional after-sale-service wrapping engineers all over the country, 
15 PUR machine has the features of High efficiency, high speed,  about 1-60m/miunute, suitable for mass production.
16 flexile frames,can save much space and save time.improve efficiency.

Floor Decroative Machine

Floor Decorative Machine, Furniture Making Machine, Veneer Adhesive Machine

Shandong Qufu Xingbang Heavy Equipment Co., Ltd. , http://www.chinaxingbangheavyindustry.com